Epilog Fusion Pro Laser Machines
Introducing the new Epilog Fusion Pro. 5G acceleration and 165 IPS engraving speeds provide the fastest engraving in the industry. And the IRIS™ Camera Positioning system allows you to precisely place your artwork on screen in seconds.
- Fusion Pro 32: 32” x 20” (812 x 508 mm) work area
- Fusion Pro 48: 48” x 36” (1219 x 914 mm) work area
- Wattages:
- CO2: 50, 60, 75, or 120 watts
- Fiber: 30 or 50 watts
- Dual: Configure your laser with both CO2 and Fiber sources
Features: Benefits of Epilog’s Fusion Pro Laser System
The Fusion Pro laser engraving and cutting machines from Epilog are our top-of-the-line laser systems and combine a large work area with the latest technological features, including:
Gravure ultra rapide sur une surface de travail plus importante
The Fusion Pro’s 165 IPS engraving speed and 5G acceleration combine to provide the fastest engraving in the industry.
IRIS™ Camera Positioning
Overhead cameras provide an accurate picture of the working area for accurate artwork placement, and a camera at the lens allows the system to find preprinted registration marks.
Touch Screen at the Laser
Select between jobs, change settings, and more right from the easy-to-use touch screen interface right at the laser. Rerun jobs at the touch of a button.
Conçus et fabriqués aux États-Unis
Proudly designed, engineered, and manufactured in our Golden, CO headquarters at the base of the Rocky Mountains.
Mettez votre système laser en réseau dans votre installation
The Fusion Pro features built-in Ethernet, USB, and a new wireless connection for more options for networking your laser.
SAFEGUARD™ Features
Keep the mechanics of your laser machine cleaner than ever before with side bellow enclosures, a fully covered x-axis assembly, and covered lens assembly.
Air Assist and Compressor
The air assist removes heat and combustible gases from the cutting surface for a cleaner cut. A built-in air compressor provides air directly to the work surface.
Table Choices
On the Fusion Pro 48 mix and match your table across the bed with optional slat and gridded cutting tables.
Radiance™ Beam Enhancing Optics
No additional, expensive lens package needed for the highest resolution engraving across the entire table.
Tubes lasers Waveguide CO2 d'Epilog
Conception à tubes métalliques pour une meilleure qualité de faisceau et une plus grande durée de vie avec des coûts de recharge réduits.
1 GB Memory in the Machine
Improve job management and data integrity with 1GB of RAM in both Fusion Pro systems. Save your most run jobs right at the laser.
Long-Life Steel Bearing
A dual block design provides the most rigidity and reduced vibration without the inevitable wobble and replacement of plastic bearings.
Accessoires
Option double source : CO2 et fibre
Are you looking for the material versatility of a CO2 laser in addition to the direct metal etching of a fiber laser? Add on the dual source option to your Fusion Pro by choosing both a CO2 laser (50, 60, or 75 watts) and a fiber laser (30 or 50 watts) to work with a wider range of materials.
Rim-Style Rotary Attachment
Available for the Fusion Pro, the Rim-Style rotary attachment adds the ability to engrave bottles, glasses, flashlights, or any other cylindrical item. The Fusion Pro rotary attachment is as easy to setup as placing your product on the rotary, raising or lowering the scissor lift to level the engraving area, and printing to the laser.
Support rotatif mandrin à trois mâchoires
The Fusion Pro 3-Jaw Chuck mechanically clamps a cylinder or oddly-shaped, non-cylindrical item in place as the laser engraves. It is the perfect accessory when your engraving requires extremely precise positioning on your cylindrical items.
Logiciel PhotoLaser Plus
PhotoLaser Plus takes photo engraving with your Epilog Fusion Series laser to the next level by easily processing photos for engraving on all types of materials. Epilog Laser has partnered with CADLink to bring you the industry’s best photo processing software: PhotoLaser Plus. The easy-to-use software interface and powerful photo processing tools allow you to create the highest-quality photo engravings in the industry.
Lentilles en option
1.5” Lens: Highest-Resolution Engraving
Although the standard 2” lens provides amazing detail, our 1.5” lens assembly has been designed for the highest-resolution engraving and etching of extremely small fonts.
4.0” Lens: Cutting Thicker Materials and Inside Deep Areas
The 4” lens produces a focused beam over a longer vertical distance, which makes it ideal when engraving within a recessed area of a product, such as inside a bowl or plate. The lens is also used for cutting through very thick materials.
Cone Lens: Deep cutting with the Laser
The cone design pushes the stream from the Air Assist directly down through the cut, rather than over the surface of the engraving material. This provides even better reduction of laser flare-ups and better edge quality.
Cutting Pin Table
La table à picots comprend des picots amovibles que vous pouvez placer où vous voulez sur la grille de perforations espacées de 25,4 mm (1 pouce). Ces picots servent également à lever et soutenir le matériau à découper là où le laser ne passera pas, ce qui permet d'éliminer les reflets au dos du matériaux. Vous pouvez aussi placer des picots pour soutenir les parties qui se détachent pendant la découpe. La plaque de surface est amovible : c'est plus pratique pour éliminer les petites chutes sans avoir à démonter la table entière.
Epilog Fusion Pro Technical Specifications
| Fusion Pro 32 | Fusion Pro 48 | |
|---|---|---|
| Zone de travail | 32” x 20” (812 x 508 mm) |
48” x 36” (1219 x 914 mm) |
| Maximum Z-Depth | 12.25” (311 mm) | 12.25” (311 mm) |
| Laser Tube Wattage |
CO2 - 50, 60, 75, or 120 watt
Fiber - 30 or 50 watt
|
|
| Logiciel | Epilog Laser Software Suite: Laser Dashboard & Epilog Job Manager | |
| Mémoire | Multiple files up to 1 GB. Engrave any file size. | |
| Modes de fonctionnement | Optimized Raster, Vector, and Combined Modes | |
| Commande de mouvement | High-speed, continuous-loop, brushless DC servo motors using rotary encoding technology for precise positioning | |
| Paliers sur l'axe X | Ground & polished stainless steel, Teflon-coated, self-lubricating bearings. Dual blocks on X-axis for greater rigidity | |
| Courroies | Advanced B-Style Kevlar belts (x-axis) and steel cord (y-axis) | |
| Résolution | Fully-flexible and user-controlled from 75 – 1200 dpi | |
| Speed and Power | Computer-controlled in .001 increments up to 100% | |
| Interface d'impression | 10Base-T Ethernet, USB, or Wireless connection. Windows 7/8/10 compatible | |
| Dimensions (L x P x H) | 54.6” x 34.2” x 42" 1387 x 869 x 1067 mm |
70.6” x 51.3" x 42.75" 1794 x 1304 x 1086 mm Pedestal removed: 34” H (863 mm) |
| Poids | 400 lbs (182 kg) | 500 lbs (227 kg) |
| Électrique | 240 volts, 50 or 60 Hz, single phase | |
| Ventilation | 650 CFM (1104 m3/hr) external exhaust to the outside or internal filtration unit required. Three output ports, 4” (102 mm) diameter. | |
| Exhaust Ports | One output port 4” (102 mm) |
Two output ports 4” (102 mm) |
| Vacuum Table Port | Additional port for dedicated exhaust through table, 4” (102 mm) | |
| Sécurité | Class 2 Laser Product – 1 mW CW Maximum 600 – 700 nm | |
Epilog Fusion Pro Material Compatibility
| Graver | Découpe | |
|---|---|---|
| Bois | x | x |
| Acrylique | x | x |
| Tissu | x | x |
| Verre | x | |
| Métal revêtu | x | |
| Céramique | x | |
| Delrin | x | x |
| Toile | x | x |
| Cuir | x | x |
| Marbre | x | |
| Carton mat | x | x |
| Mélamine | x | x |
| Papier | x | x |
| Mylar | x | x |
| Bois pressé | x | x |
| Caoutchouc | x | x |
| Vernis à bois | x | x |
| Fibre de verre | x | x |
| Métaux peints | x | |
| Carrelage | x | |
| Plastique | x | x |
| Liège | x | x |
| Corian | x | x |
| Aluminium anodisé | x | |
| Acier inoxydable | * | |
| Laiton | * | |
| Titane | * | |
| Métaux nus | * | |
| * Les lasers au CO2 peuvent marquer le métal nu recouvert d'une solution de marquage adaptée. Pour plus d'informations, rendez-vous sur notre page consacrée au marquage au laser du métal. | ||
| Vous avez des matériaux à tester ? Notre équipe Applications sera heureuse de vous aider. | ||
Demande d'informations supplémentaires
Recevez une brochure et des échantillons
Recevez des brochures et des échantillons et obtenez davantage d'informations de notre part ou de votre distributeur local.
Principal contenu
2019 © Epilog Laser. ALL Rights Reserved. Privacy Policy | Choose Your Country | Sitemap